How to replace Dock Connector in your iPad2 GSM?

 

So recently you started having charging issues with your iPad2 GSM. You attach the USB Connector Cable which does not recognize your iPad2 device.

Then you’re being informed by your nearby repair shop that your particular device has a faulty Dock Connector which requires an immediate replacement. Now in case if you don’t want to incur the cost of its heavy repair, so before you head over to Contact Apple for support and service you can even opt for its DIY repair which would be quite cost effective.

Reminder: In case if your device is under warranty period then you better get it repaired from an authorized iPad repair centre before going for a DIY repair.

iPad 2 GSM Dock Connector Replacement: Replace the Dock Connector in your iPad 2 GSM.

IPAD2-DOCK-CONNECTOR

 Tools required:

  • Heat gun or an iOpener.
  • Phillips #00 Screwdriver.
  • Plastic razor tool.
  • Plastic Picks.

How to replace Dock Connector in your iPad2 GSM?

Replace the Dock Connector in your iPad 2 GSM.iPad 2 GSM Dock Connector ReplacementiPad 2 Charging Port Dock Connector RepairInstalling iPad 2 GSM Dock ConnectorHow to replace your iPad dock connector:  iPad 2 GSM Dock Connector ReplacementCharging Dock Repair - iPad 2 GSM How to Tutorial

IPAD2-DOCK-CONNECTOR Step 1:

  • Just power off your iPad2 device, before you start its disassembly process.
  • Then place the heated iOpener flat or use your heat gun, on the iPad’s right edge to smooth out the adhesive in that very section for about 90 plus seconds before your attempt to pry up its front assembly panel.

IPAD2-DOCK-CONNECTOR Step 2:

  • Now carefully wedge the plastic razor tool’s tip into the small gap, just enough to widen the crack, right in between the plastic bezel and the front glass.

Reminder: Now it might need a bit of force to wedge the plastic tool’s tip right between the bezel and the glass. So workout carefully and patiently to wiggle the plastic razor tool back and forth as needed.

  • Now just hold the plastic razor tool inserted right in between the plastic bezel and the front glass and then slide a plastic pick in the small opening nearest the plastic razor tool.
  • Then detach the plastic razor tool out of the iPad and insert the plastic pick further beneath the front glass to about 0.5 inches deep.
  • While releasing the adhesive on the iPad’s right side, just reheat your iOpener or use your heat gun to warm up the iPad’s bottom edge.
  • Now while the iPad’s bottom edge is being warmed up, just start to release the adhesive alongside the iPad’s right edge.
  • Then just slide the plastic pick down alongside the iPad’s right edge to release all the adhesive coming in its way.
  • Now just before detaching the first plastic pick away from the iPad’s bottom corner, carefully wedge another pick right beneath the front glass’s right edge to prevent the adhesive from re-sticking.
  • Again use the heat gun or re-heat your iOpener to smooth up the iPad’s top edge.
  • Then slide the plastic pick just around the iPad’s bottom right corner to release the adhesive in that section.

Reminder: Just avoid sliding the plastic pick further than the iPad’s bottom right corner as the Wi-Fi antenna might get damaged in the process.

  • Don’t detach the plastic pick fully and away from beneath the front glass. Just pull that pick out a little bit till about 1/8 mm of its tip is still remaining beneath the front glass.
  • Then slide the plastic pick’s tip right along the iPad’s bottom edge to release the Wi-Fi antenna adhesive.
  • After passing the Wi-Fi antenna, which is about 3mm away from the iPad’s right edge or is quite near the home button, just re-wedge the plastic pick deep enough.
  • Then slide the plastic pick towards the right to release the adhesive attaching the Wi-Fi antenna with the front glass.
  • Just keep on releasing the iPad’s bottom adhesive and pull out the plastic pick just enough to move about the home button. Then again re-wedge it after the pick passes the home button.
  • Again keep on releasing the entire adhesive all along the iPad’s bottom edge.
  • Just hold the plastic pick inserted right beneath the front glass next to the home button.
  • Again use your heat gun or reheat your iOpener to warm up the adhesive in the iPad’s left edge section.
  • Then carefully slide the plastic pick along the iPad’s top edge to slightly pull it out in order to move about the front camera bracket.
  • Again keep on releasing the iPad’s top edge adhesive and gently slide the plastic pick just about the iPad’s top left corner.
  • Then slide the plastic pick alongside the iPad’s left edge to release the adhesive coming its way.

Reminder: Now the digitizer cable is about 2.0 mm away from the iPad’s bottom. So, just halt the sliding job when you reach about 2.30 mm away from the iPad’s bottom.

  • Use your plastic pick which is still held beneath the iPad’s bottom edge to release the iPad’s bottom left corner adhesive.

Reminder: Now the digitizer cable’s bottom is just about 1 inch from the iPad’s bottom. Just make sure that this cable is not severed.

  • Use one of your plastic picks to open up the iPad’s bottom right corner and hold it firmly with your fingers.
  • Then just firmly grab the iPad by its bottom as well as its right corners and gently remove the front glass out of your iPad.

IPAD2-DOCK-CONNECTOR  Step 3:LCD:

  • Now use your Phillips screwdriver to unscrew and remove all the four 2.0 mm Phillips #00 screws attaching the LCD with the back case.
  • Then just raise the LCD by its longer edge nearest the volume buttons and flip it out of the back case.
  • Gently place the LCD over the front panel.

IPAD2-DOCK-CONNECTOR Step 4:Dock Connector:

  • Now use your plastic razor tool to peel off the tape piece wrapped over the dock connector cable’s end.
  • Then use your plastic razor tool’s edge to gently detach the dock cable connector away from its socket on the logic board.
  • Just peel off the dock connector ribbon cable away from the back panel.

Reminder: Now don’t attempt to detach the cable completely, as it might still be attached with the back panel.

  • Unscrew and remove both of the 2.0 mm Phillips screws attaching the dock connector with the back panel.
  • Gently detach the dock connector away from the back panel’s edge and carefully pull it from your device.
  • Now you’re holding the bare dock connector.

IPAD2-DOCK-CONNECTOR Step 5:

  • Replace the old dock connector with the new connector.
  • To reassemble your iPad2 GSM device, just follow all the above steps in exact reverse order.

Now you’ve successfully replaced the dock connector of your iPad2 device. For immediate assistance, Contact Apple customer services department could, all you have to do is call the apple support phone number from a BT landline and you will be directed straight through to Apple helpline UK.

Leave Your Comment