How To Replace Your iPad 2 CDMA Headphone Jack ?

iPad 2 CDMA problemiPad 2 CDMA Headphone Jack ReplacementiPad 2 CDMA problem

So the headphone jack of your iPad2 device has started giving you issues. Sometimes you only hear a single channel which is just the background music without any voice or vice versa. And when you jiggle its jack the sound gets more distorted.

You tried to reset all its original factory settings; you cleaned the jack and inspected all the problems related with it; you tried every damn thing but nothing seemed to fix the problems. Then you were informed by some repair shop that the headphone Jack of your iPad2 device needs an immediate replacement which would burn a hole in your pocket.

Now you wish to opt for its DIY repair which is quite possible but is very difficult to perform. Be prepared with enormous patience, all the correct repair tools as well as ample spare time.

NOW AVAILAIBLE :pu_new(Free/Xclusive)Call Now : Apple Customer Support

iPad 2 CDMA Headphone Jack Replacement

iPad 2 CDMA problem

Tools required:

  • Heat gun or an iOpener.
  • Plastic Picks.
  • Phillips #0 Screwdriver.
  • Phillips #00 Screwdriver.
  • Plastic razor tools.

iPad 2 CDMA problemStep 1:

  • Just Switch off your iPad2 device, before you start to disassemble it.

iPad 2 CDMA problemStep 2:

Front assembly:

  • Then place the heated iOpener flat or use your heat gun, on the iPad’s right edge to smooth out the adhesive in that very section for about 90 plus seconds before your attempt to pry up its front assembly panel.
  • Now carefully wedge the plastic razor tool’s tip into the small gap, just enough to widen the crack, right in between the plastic bezel and the front glass.

Reminder: Now it might need a bit of force to wedge the plastic tool’s tip right between the bezel and the glass. So workout carefully and patiently to wiggle the plastic razor tool back and forth as needed.

Related: How to Replace Loud Speaker Assembly of iPad2 CDMA?

  • Now just hold the plastic razor tool inserted right in between the plastic bezel and the front glass and then slide a plastic pick in the small opening nearest the plastic razor tool.
  • Then detach the plastic razor tool out of the iPad and insert the plastic pick further beneath the front glass to about 0.5 inches deep.
  • While releasing the adhesive on the iPad’s right side, just reheat your iOpener or use your heat gun to warm up the iPad’s bottom edge.
  • Now while the iPad’s bottom edge is being warmed up, just start to release the adhesive alongside the iPad’s right edge.
  • Then just slide the plastic pick down alongside the iPad’s right edge to release all the adhesive coming in its way.
  • Now just before detaching the first plastic pick away from the iPad’s bottom corner, carefully wedge another pick right beneath the front glass’s right edge to prevent the adhesive from re-sticking.
  • Again use the heat gun or re-heat your iOpener to smooth up the iPad’s top edge.
  • Then slide the plastic pick just around the iPad’s bottom right corner to release the adhesive in that section.

iPad 2 CDMA problemReminder: Just avoid sliding the plastic pick further than the iPad’s bottom right corner as the Wi-Fi antenna might get damaged in the process.

Related: How to Repair Left Right Cellular Data Antenna of iPad2 CDMA?

iPad 2 3G CDMA Headphone Jack 821-1462-04

iPad 2 3G CDMA Headphone Jack 821-1462-04

  • Don’t detach the plastic pick fully and away from beneath the front glass. Just pull that pick out a little bit till about 1/8 mm of its tip is still remaining beneath the front glass.
  • Then slide the plastic pick’s tip right along the iPad’s bottom edge to release the Wi-Fi antenna adhesive.
  • After passing the Wi-Fi antenna, which is about 3mm away from the iPad’s right edge or is quite near the home button, just re-wedge the plastic pick deep enough.
  • Then slide the plastic pick towards the right to release the adhesive attaching the Wi-Fi antenna with the front glass.
  • Just keep on releasing the iPad’s bottom adhesive and pull out the plastic pick just enough to move about the home button. Then again re-wedge it after the pick passes the home button.
  • Again keep on releasing the entire adhesive all along the iPad’s bottom edge.
  • Just hold the plastic pick inserted right beneath the front glass next to the home button.
  • Again use your heat gun or reheat your iOpener to warm up the adhesive in the iPad’s left edge section.
  • Then carefully slide the plastic pick along the iPad’s top edge to slightly pull it out in order to move about the front camera bracket.
  • Again keep on releasing the iPad’s top edge adhesive and gently slide the plastic pick just about the iPad’s top left corner.
  • Then slide the plastic pick alongside the iPad’s left edge to release the adhesive coming its way.

Reminder: Now the digitizer cable is about 2.0 mm away from the iPad’s bottom. So, just halt the sliding job when you reach about 2.30 mm away from the iPad’s bottom.

  • Use your plastic pick which is still held beneath the iPad’s bottom edge to release the iPad’s bottom left corner adhesive.

Reminder: Now the digitizer cable’s bottom is just about 1 inch from the iPad’s bottom. Just make sure that this cable is not severed.

  • Use one of your plastic picks to open up the iPad’s bottom right corner and hold it firmly with your fingers.
  • Then just firmly grab the iPad by its bottom as well as its right corners and gently remove the front glass out of your iPad.

iPad 2 CDMA problemStep 3:

LCD:

  • Now use your Phillips screwdriver to unscrew and remove all the four 2.0 mm Phillips #00 screws attaching the LCD with the back case.
  • Then just raise the LCD by its longer edge nearest the volume buttons and flip it out of the back case.
  • Gently place the LCD over the front panel.

iPad 2 CDMA problemStep 4:

Headphone Jack Assembly:

Related: How to Replace Logic Board of your iPad2 GSM?

  • Use your plastic razor tool’s flat end to gently toss the retaining flap up on the headphone jack as well as the front camera ribbon cable ZIF socket.

Reminder: Make sure you are flipping up only on the hinged retaining flap and not the entire socket.

  • Slide your plastic razor tool just beneath the headphone jack as well as the front camera cable to release it away from the adhesive sticking the cable with the back panel.
  • Now gently pull and detach the headphone jack as well as front camera ribbon cable away from its socket on the logic board.
  • Unscrew and remove both of the 2.9 mm Phillips screws attaching the headphone jack with the back panel.
  • Use your plastic razor tool to release the headphone jack out of its recess in the iPad’s top edge.

Reminder: Don’t attempt to detach the assembly just yet.

Related: How To Replace Microphone in your iPad 2 GSM

  • Cautiously peel off the front camera as well as the microphone cables away from the back panel.
  • Cautiously peel off the tape strip wrapped around the front camera cable connector.
  • Use the plastic razor tool’s edge to detach the front camera cable away from the headphone jack cable.
  • Again cautiously peel off the front camera cable away from the bottom ribbon cable secured with the headphone jack.

iPad 2 CDMA problemStep 5:

Headphone Jack removal:

  • Use the plastic razor tool’s edge to carefully detach the microphone cable connector.
  • Gently pull the headphone jack out of your iPad 2.

iPad 2 CDMA problemStep 6:

  • Replace the old faulty headphone jack with your brand new jack.
  • Now to reassemble your device, carefully follow all the above instructions in exact reverse order.

Now you’ve successfully replaced the headphone jack of your iPad2 CDMA.

 

Related:

How To Replace My iPad Battery?: iPad Problems

iPad Problems: How To Replace iPad LCD?

How To Repair iPad 3G Logic Board?

How to Repair iPad 3G Ambient Light Sensor?

How To Replace Your iPad 2 GSM Home Button Assembly?

How To Fix iPad 2 GSM Broken LCD ?

How To Fix Front Facing Camera Of iPad 2 GSM?

How To Replace Display Data Cable in iPad 2 GSM?

Leave Your Comment